东莞品优自动化设备有限公司

Dong Guan Pin You Co.,Ltd.

热转印机厂家

服务热线

076982863379

联系我们

英文200热转印机器说明书

文章来源:haibin172 人气: 1,262 发表时间: 05-23

Manual operation

 

 

 

PinYou Automation Equipment CoLtd

http://www.cnbinyou.com

http://cnpinyou.1688.com                             

TEL : +86-13825750827

                          FAX: 86-769-82863379

                          E-mail: cbp3@163.com

 

 

Specifications

1.(Plane)Max Printing:250*300mm

2.(Cylinder)Max Printing:¢200mm

3.Length of Rubber Roller: 150mm

4.Working table area: 600*200 mm

5.Stamping speed:500-1000P/hour

6.Max pressure:1300 Kg

7.Up-and down distance: 80 mm

8.Table Stroke: 300 mm

9.Heat wattage: 1600 W

10.Temperature range:0 – 400oC

  1. Max Oil Pressure: 70kgf/cm2′

12.Wattage:220V/50Hz

13.Foil feed: Motor Drive

14.Air Pressure:0.5-0.7MPa

15.Net Weight :295 Kg

16.Outer dimension:1100 x 850 x 1700 mm .

 

 

 

Machine characteristics:

 

  1. Data protection when it is emergency power-off:The computer board would save informations when it is emergency power-off.

Printing account is 0-99999 times, it will be cleared zero automatic when it power on again.

 

2 Multi-functional IC electronic controller ensure that the machine function of flat stamp, rolling stamp,flat pressing the round surface, etc.

 

  1. Bent elbow structure low air consumption and strength steady pressure.

 

  1. Stamping pressure, temperature and time are adjustable.

 

5 worktable can be customized to move back and forth automatically, which be operation facilitate safe and fast.

 

  • Worktable can sway rotary around the center of rotation to ensure the workpiece swing without sliding.

 

  1. Adjustable automatic hot foil feeding and foil delivery.Used Taiwan OUTAI motor. It can be customized to be more precise two-speed foil delivery.

 

8 installation of photocell (Taiwan FOTEK electric eye can work precise 250 times per second) can follow-up and control the heat transfer paper with the anchor point.

  1. The movement height of hot stamping head can be adjustable, which can stamp bigger workpiece with 300mm height.

 

  1. It can be customized to Germany cylinder (super wear-resistant seals). Used Taiwan Mindman Solenoid valve to control precise,Germany NASS coil is stable and durable.

 

  1. Flat driving worktable use the wind conversion device, which ensure the working mechanism drives the workpiece rotary stamping smoothly,and keep the stamping effective.

 

  1. It can be customized to be horizontal,hydraulic and grinder cross-bench worktable according to customer requirements, two-speed hot foil delivery, plus rodless cylinder to access automatic , roll-to-roll stamping, stamping irregular shaped product, etc.

 

  1. With emergency stop safety device to protect the safety of the operator.

 

  1. One year warranty and lifetime maintenance for all parts components for free . With manual operation, a toolbox, one time free training and proofing samples.

 

  1. the under high temperature heating head need to be settled the function of delay roll, then can avoid the silicone roller be damage by high temperature.

 

16.plastic rollers, screws, and other quick-wearing parts need to get cost when it damaged by man-made damage.

 

 

Button function:

 

 

  1. “Pause/Start”button: In standby, press the “Pause/Start” button, the machine is running according to the parameters set, indicator light is on; during operation of the machine press the “Pause/Start” button again, the machine stops running, indicator light is off; the initial standby .

 

  1. “Heating”button: press the” heating” button, the heating is turned on, indicator light is on; press the ” heating” button again, the heating is turned off, indicator light is off;the initial off.

 

  1. “Shuttle” button: press the “shuttle” button , shuttle worktable begin working , indicator light is on; press the “shuttle” button again, shuttle worktable stop working, indicator light is off; the initial off.

 

4 “clear ” button: press “Clear” button, all count will be clear.

 

5 “Photo Sensor winding “button:open- the “Photo Sensor winding ” motor begin to work.

Off – the motor stops.

 

6 ” under press”button: open – hot head press under.

Off – hot head come back into position.

 

  1. When the power switch is turning on, the panel temperature can show to room temperature, time can show the worktable be start delayed, then it can work properly.

Otherwise it is necessary to detect the temperature line and the probe is normal or not.

 

 

 

  1. “Tep Setting”:

A: Press the “temperature”button, it shows the initial temperature, the last number  beat once a second. Now can change the temperature by press “+”and “-” button. If don’t press any button within 5 seconds, the window will show the current temperature. If press other button except “+”, “-“, “displace” button, it will confirm the current temperature.

 

2.Stamping Time

A: press the “Stamping Time” button, it shows the initial stamping time, the last number beat once a second. Now can change the stamping time by press “+”,  “-” and “displace” button. If don’t press any button within 5 seconds, the window will show the current stamping time. If press other button except “+”, “-“, “displace” button, it will confirm the current stamping time.

 

B: Hold the “Stamping Time” button five seconds, it shows the shuttle worktable is starting delayed, the last number beat once a second.Now can change the delay of stamping time by press “+”, “-” and “displace” button. If press other button except “+”, “-“, “displace” button, it will confirm the current stamping time.

 

  1. Winding Setting

A: press the “Winding Setting”button, it shows the initial time winding, the last number beat once a second. Now can change the time winding by press “+”,  “-” and “displace” button. If don’t press any button within 5 seconds, the window will show the current time winding. If press other button except “+”, “-“, “displace” button, it will confirm the current time winding.

 

B: Hold the “Winding Setting” button five seconds, it shows the Photo Sensor winding is starting delayed, the last number beat once a second.Now can change the delay of winding time by press “+”,  “-” and “displace” button. If press other button except “+”, “-“, “displace” button, it will confirm the current winding time.

 

 

  1. Modify the function of hot stamping/heat transfer.

Press the “Manual/Auto” button 10 second. It is heat transfer function when the

light on the bottom right corner is on. It is hot stamping function when the light is off.

Press the”flat”button, the heat head is under and stop; press the “cylinder” button,

the heat head is under but continue to work.

 

 

Circuit diagram of hot stamping foil

 

      

Wiring diagram

                            

 

                      Daily maintenance               

  1. Keep the machine clean and tidy, and place the tools back to.

 

  1. Remove the water from the air filter. Working pressure set to 4 ~ 5bar pressure can work.
  2. When the machine is working, cannot blowing directly to the machine by the mechanical fan or air conditioning, it will affect its mechanical temperature control system.

 

  1. Need to put the lubrication oil on the activities spare parts once a week.

Such as the font & back sliding rails of worktable, rubber rollers rotating gear chain, adjusting screw, and the up & down slipping guide of hot head.

 

  1. It can’t off the power supply immediately after the production. Just close the switch of panel. Otherwise, the rollers will be damaged easy. Set the machine to off automatic after 30 minutes.

 

  1. When it is stamping, please ensure the rubber roller contact closely with the stamping surface. The rotation speed of hot head must be slower than the working speed of shuttle worktable, otherwise it will burn the hot foil and rubber roller.

 

  1. Non-maintenance operations personnel do not arbitrarily open electrical boxes, panels, and do not arbitrarily twist knob switch.

 

  1. Heat transfer and hot stamping operation is very high temperature and high risk.

The workers must be trained and qualified their posts before begin to use the machine.

It is better to arrange two or more people work together, which can take the proper remedial measures in case of accidents.

 

  1. It is not at liberty to add a foot switch device for heat transfer machine and hot stamping machine. or it is easy to burn hands and skin.

 

  1. In the process of the machine operation, the panel power supply must be switched off. Otherwise, the worker maybe touch the button by mistake, and some accident happens.

When the machine is running, prohibit to change the relevant button, which maybe cause some accident.

 

  1. Voltage instability region need to add voltage stabilizer, Electricity must be effectively grounded; If the workshop has the frequency conversion device such as a radio frequency instrument or machine, it need isolate effectively. Otherwise it will damage the machine, even an accident happened for workers.

 

  1. When the power switch is turning on, the panel temperature can show to room temperature, time can show the worktable be start delayed, then it can work properly. Otherwise it is necessary to detect the temperature line and the probe is normal or not.

 

  1. The machine is free warranty for one year, life-long maintenance.Related accessories cost charge after warranty period. Artificial damage or other art factor and wearing parts is not in the warranty scope and so on.

 

 

 

 

076982863379

Copyright © 2018 热转印机器,热转印设备,花膜,热转印机 版权所有  粤ICP备16064803号

技术支持:东莞品优自动化设备有限公司 版权所有

关键词:热转印机,热转印设备,热转印机器,热转印膜,热转印,广东热转印,全自动热转印机

热转印设备多少钱 热转印机生产厂家 热转印技术